By DangleContributor @carterofmemphis
It’s been a fun summer huh? Camping, swimming exploring, backcountry ragers, and of course good ole Dangle Bong has been along for the party, right? Did you name it? Bedazzle it, we bet you did, and we’d love to see your customizations for aesthetics or functionality. Where were we, oh yeah last summer, whew! Did your Dangle Bong get dirty? No problem, our sturdy titanium construction and a few hacks from our field guide makes clean up a breeze.
Dan would like to mention that dangling, like life will be much easier if you remember to Always Bring Your Towel (paper towel that is). In order to maintain and effectively use your dangle bong we recommend the following be brought along when operating your Dangle Bong in the field. DIY tOkesPoke: take an old bicycle spoke, snip it, and push it into your cork for later maintenance.Danglebong – Clip it, stow it, let it fly!
- Cork – This keeps everything snug and together.
- NugHuggerTM – Stash this piece in your cork
- Toke Spoke – The little pusher that could, stash this in your cork as well.
- Paper towel – a couple sheets is fine here, just keep it dry till you need it.
- Lighter- For heating stuff.
- Knife - For Cutting & Scraping stuff.
While undergoing regular use it is normal that detritus and resins may collect on your Danglebong system we have found the following to be a quick and easy way to keep things looking like new. The following guide assumes you have some limited access to water and common sense:
Do you know where your towel is? Take your field kit out as described above. Prepare NugHuggerTM for cleaning by heating it slightly either through normal use or holding a lighter over the bowl area for 30-45 seconds. We aren’t trying burn anything off here, just make things move a little quicker for the next step.
FYI: if you’re an old pro and prefer isopropyl alcohol and salt go to town chief, this write up here is for our field officers doing us proud out in the wilds of where-ever-the-fuck. This step produces nasty, sticky, icky, goop that will add a very “authentic” patina to anything it touches. If this is not your intent, angle your dangle towards a cat hole, trash can, or preferred waste receptacle BEFORE you start cleaning. Once the resin is out of the tube and out rolling around in the world, things get messy quickly. We cool? Okay let’s move on.
1. As shown take your toke spoke and a small 1” x 1” strip of paper towel and roll it into a little tube. Put the paper into the back of the NugHuggerTM and set your tOkeS-pokE on the paper to push through the hole. Push slowly and evenly while turning the piece to insure proper cleanage.
2. Take your knife and angle it to run straight along the inside of your bowl to catch any buildup collected there. Wipe the knife blade off on a paper towel and heat knife edge to remove any extra buildup.
3. You may need to repeat step 2 again if after step 3 some buildup clogged the hole. After this the NugHuggerTM should be good to go.
4. The main body of Dangle cleaning need not be done terribly often. When needed, use warm soap & water and rinse with an old toothbrush or scrubber. This should remove all buildup and keep things shiny.
5. Now go back to the operations guide and figure out how we got in this mess in the first place.
—Dan 'Dan Gullbongs' Gullbongs
Learn how to operate your new Titanium Bong
By DangleContributor @carterofmemphis
So, you want to know how maximize the potential of the ole Dangler eh? While your mileage may vary, and we could pontificate at length about technique, what follows is a basic guide for the uninitiated.
1. Laugh a little bit because smoking drugs is not serious.
2. Fill the DangleBong main chamber with 1-1.5oz. of clean water. Do not use other liquids. Using crushed ice is with a dollop of water is super cool. Draw through the device once or twice cautiously to draw all the excess water out of the chamber so it doesn’t interfere with the oncoming party.
3. Take the NugHuggerTM and fill it to your preference with the material of your choice. Insert the stem into the device.
4. Light the business end of the device and draw easily. When it seems like you are nearing capacity rip the NugHuggerTM from the base of the Dangle and enjoy.
5. Re-insert the NugHuggerTM into the base and repeat as desired.
Don't be one of those gross bong-dummies who leaves water in their device. Pour out water on a plant friend in need, and then run a clean rag through your Dangle to limit moisture buildup and mold potential in the device. Stow everything in the cork top securely so it doesn’t come undangled on you.
Storage: When you aren’t actively traveling with your DB the best practice is to pull the cork away from the base and the NugHuggerTM away from the cork. Let it chill like this till you need it again.